How to Make Glass Cabinet Doors With Wood Frames

How to Make Glass Cabinet Doors With Wood Frames

Universal cabinet doors are usually made of a solid wood sheet development. While they make an immaculate showing of keeping the substance of the cabinet held, they additionally cover them from perspective. In the event that you'd rather have the substance effortlessly seen while pressing on to keep them safely put away, you'll have to change the solid wood cabinet doors to doors of glass. Changing the existing doors is conceivable, yet usually not worth the time and exertion. Instead, you can make your own framed glass cabinet doors, measured to fit your cabinets impeccably, with just a couple needed tools.

  1. Unfilled out all things from the cabinet to abstain from damaging them throughout the cabinet door replacement transform.
  2. Remove the screws from the pivots holding the existing cabinet doors in place with a Phillips-head screwdriver. Pull the doors from the front of the cabinet and after that set them aside onto an even surface. Measure the extents of the cabinet doors with a measuring tape, taking both the length and width of the cabinet doors.
  3. Set the work-stop hinder on the saw rail to the measured length of the cabinet doors. Place the board onto the saw rail, and afterward slice through the board with the saw razor sharp edge. Cut two length sheets for every cabinet door. Cut two width sheets using the same cutting process for the width measurement of the cabinet.
  4. Make lap joints on the close of each of the curtail sheets using a switch set to cut into the substance of the board, 50% of the board's thickness. Set a rail on top of the sheets as an aide for the switch, setting the rail onto the substance of the board divided the precise measured width of the board, from the board's close. This will give you a cut on the board that is half the board's profundity while being the width of the other board covering the cut.
  5. Brush yellow wood glue over the tracked decreases with a paintbrush. Press the reduce on a width board over the decrease on a length board to make a cover where the corners of the joint are 90-degrees, and the overlapped region is the same tallness as whatever remains of the board. Rehash the procedure for the other three joints of the cabinet doorframe to make a frame that is the same measure as the definitive cabinet door. Place brad nails through the covering board segments to secure the frame as the glue dries.
  6. Replace the spot in the switch with a round-over touch. Set the touch profundity to in the ballpark of 1/4-inch, then after that run the switch over the edges on the front of the board to balance them for a more magnetic look.
  7. Change to a rabbet chomped in the switch, then after that flip the board over with the intention that you can cut along the back. Set the touch profundity to around the range of 1/4-inch then afterward reduce a minor rabbit ledge on the inside edge of the frame to hold the glass in place. Remove the corner material left by the rabbit nibbled with a mallet and etch to make 90-degree edges for the rabbit ledge. Make a rabbet on the outside of the back frame too, to consider proper fitting of the cabinet door inside the cabinet opening.
  8. Paint or stain the frame the color coveted, applying the paint or wood stain with a paintbrush.
  9. Measure the space between restricting rabbet edges on the interior of the frame, and have a 1/8-inch thick sheet of glass slice to match the measurement. Place the glass into the frame along the ledge.
  10. Place a 1/8-inch thick attendant strip the same width as your rabbet ledge between the glass surface and the bottom surface of the frame behind the glass, and push it to the edge of the frame. Nail the strip in place by pushing little brad nails through the edge of the strip and into the frame with a brad pusher each 6-inches, from the side of the strip confronting the glass.
  11. Screw the pivots onto the new glass cabinet door, then after that screw the cabinet door handles onto the fronts. Place the door onto the cabinet and screw the pivots to the cabinet frame to complete the installation of the new glass cabinet door.

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>